ISO 10332:2010 PDF

Non-destructive testing of steel tubes — Automated ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for verification of hydraulic leak-tightness

Первая страница стандарта ISO 10332:2010

Открыть превью (PDF)

Название (английский):

ISO 10332:2010

Non-destructive testing of steel tubes — Automated ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for verification of hydraulic leak-tightness

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 7
Дата публикации:: 29 сентября 2010 г.
Издание:: ISO IS 10332 edition 2 version 1
ICS:: 23.040.10

Язык документа:

ruen

Срок поставки:2 раб. дн. (перевод)

Цена:105 €

Описание (английский):

ISO 10332:2010 specifies requirements for automated ultrasonic shear-wave (generated by single element probes or the phased-array technique) testing of seamless and welded (except submerged arc-welded) steel tubes, for verification of hydraulic leak-tightness. The testing technique is applied for the detection of predominantly longitudinal imperfections. Where applicable, Lamb-wave testing may be applied at the discretion of the manufacturer. ISO 10332:2010 is applicable to the inspection of tubes with an outside diameter greater than or equal to 10 mm, and with an outside diameter-to-thickness ratio greater than or equal to 5.

Технические детали

Технический комитет: ISO/TC 17/SC 19 - Technical delivery conditions for steel tubes for pressure purposes
SKU: ISO 10332:2010

Abstract

Overview - ISO 10332:2010 (automated ultrasonic testing for steel tubes)

ISO 10332:2010 specifies requirements for automated ultrasonic testing (AUT) of seamless and welded (except submerged arc-welded) steel tubes to verify hydraulic leak‑tightness. The standard focuses on the detection of predominantly longitudinal imperfections using shear‑wave ultrasonic techniques (single‑element or phased‑array) and, where applicable, Lamb‑wave testing at the manufacturer's discretion. It applies to tubes with outside diameter (OD) ≥ 10 mm and OD-to-thickness ratio ≥ 5.

Key topics and technical requirements

Scope & applicability
- Seamless and welded steel tubes (SAW excluded), OD ≥ 10 mm, OD/thickness ≥ 5.
- Detects mainly longitudinal defects; Lamb‑wave optional.
Ultrasonic techniques & parameters
- Shear‑wave frequency: 1 MHz to 15 MHz.
- Lamb‑wave frequency (if used): 0.3 MHz to 1 MHz.
- Maximum transducer width for longitudinal defect detection: 25 mm.
- Maximum active aperture for phased‑array/Lamb techniques: 35 mm.
Scanning and coverage
- Tubes and transducer assembly moved relative to each other to scan the full surface; scanning in two opposing beam directions unless otherwise agreed.
- Relative speed variation during testing limited to ±10%.
- Untested short end lengths handled per product standard (see Annex A).
Reference standards & calibration
- Use of reference tubes containing calibrated notches or drilled reference holes for AUT calibration.
- Reference notch: “N” type, width ≤ 1.0 mm, depth = 12.5% of wall thickness (min 0.5 mm, max 1.5 mm) with ±15% tolerance, length > single‑transducer width (max 50 mm).
- Reference hole diameters limited by OD (specified in the standard’s table).
- Equipment calibrated at the start of each cycle (e.g., three consecutive reference passes); calibration checked at least every 4 hours, on operator change, and at start/end of runs.
- Trigger/alarm levels set using internal/external reference signals; equipment must automatically classify tubes as acceptable or suspect and support marking/sorting.
Personnel
- Operators and supervisors must be qualified per ISO 9712, ISO 11484 or equivalent.

Applications - who uses ISO 10332:2010

Tube manufacturers and mill inspection teams for production quality control and hydraulic leak‑tightness verification.
NDT service providers performing automated ultrasonic inspection of tubing used in pressure, hydraulic, and structural applications.
Purchasers and inspection authorities specifying acceptance criteria and inspection procedures in procurement contracts.
Engineering and quality teams ensuring compliance with NDT best practices for longitudinal defect detection.

Related standards

ISO 5577 - Ultrasonic inspection vocabulary
ISO 9712 - Qualification and certification of NDT personnel
ISO 11484 - Employer qualification system for NDT personnel

Keywords: ISO 10332:2010, automated ultrasonic testing, AUT, non‑destructive testing, NDT, steel tubes, hydraulic leak‑tightness, shear‑wave, phased‑array, Lamb‑wave, reference tube, calibration.

Overview - ISO 10332:2010 (automated ultrasonic testing for steel tubes)

Key topics and technical requirements

Scope & applicability
- Seamless and welded steel tubes (SAW excluded), OD ≥ 10 mm, OD/thickness ≥ 5.
- Detects mainly longitudinal defects; Lamb‑wave optional.
Ultrasonic techniques & parameters
- Shear‑wave frequency: 1 MHz to 15 MHz.
- Lamb‑wave frequency (if used): 0.3 MHz to 1 MHz.
- Maximum transducer width for longitudinal defect detection: 25 mm.
- Maximum active aperture for phased‑array/Lamb techniques: 35 mm.
Scanning and coverage
- Tubes and transducer assembly moved relative to each other to scan the full surface; scanning in two opposing beam directions unless otherwise agreed.
- Relative speed variation during testing limited to ±10%.
- Untested short end lengths handled per product standard (see Annex A).
Reference standards & calibration
- Use of reference tubes containing calibrated notches or drilled reference holes for AUT calibration.
- Reference notch: “N” type, width ≤ 1.0 mm, depth = 12.5% of wall thickness (min 0.5 mm, max 1.5 mm) with ±15% tolerance, length > single‑transducer width (max 50 mm).
- Reference hole diameters limited by OD (specified in the standard’s table).
- Equipment calibrated at the start of each cycle (e.g., three consecutive reference passes); calibration checked at least every 4 hours, on operator change, and at start/end of runs.
- Trigger/alarm levels set using internal/external reference signals; equipment must automatically classify tubes as acceptable or suspect and support marking/sorting.
Personnel
- Operators and supervisors must be qualified per ISO 9712, ISO 11484 or equivalent.

Applications - who uses ISO 10332:2010

Tube manufacturers and mill inspection teams for production quality control and hydraulic leak‑tightness verification.
NDT service providers performing automated ultrasonic inspection of tubing used in pressure, hydraulic, and structural applications.
Purchasers and inspection authorities specifying acceptance criteria and inspection procedures in procurement contracts.
Engineering and quality teams ensuring compliance with NDT best practices for longitudinal defect detection.

Related standards

ISO 5577 - Ultrasonic inspection vocabulary
ISO 9712 - Qualification and certification of NDT personnel
ISO 11484 - Employer qualification system for NDT personnel

ISO 10332:2010 PDF

Технические детали

Abstract

Overview - ISO 10332:2010 (automated ultrasonic testing for steel tubes)

Key topics and technical requirements

Applications - who uses ISO 10332:2010

Related standards

Похожие стандарты

Abstract

Overview - ISO 10332:2010 (automated ultrasonic testing for steel tubes)

Key topics and technical requirements

Applications - who uses ISO 10332:2010

Related standards

Похожие стандарты

Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2022)

Tracked Changes. Steel products. Employer´s qualification system for non-destructive testing (NDT) personnel.

Non-destructive testing - Ultrasonic testing - Vocabulary (ISO 5577:2025)