ISO 19935-2:2020 PDF

Plastics — Temperature modulated DSC — Part 2: Measurement of specific heat capacity cp

Первая страница стандарта ISO 19935-2:2020

Открыть превью (PDF)

Название (английский):

ISO 19935-2:2020

Plastics — Temperature modulated DSC — Part 2: Measurement of specific heat capacity cp

Статус документа:: Отменён
Формат:: Электронный (PDF)
Количество страниц:: 14
Дата публикации:: 23 сентября 2020 г.
Издание:: ISO IS 19935 edition 1 version 1
ICS:: 83.080.01

Язык документа:

ruen

Срок поставки:3 раб. дн. (перевод)

Цена:210 €

Описание (английский):

This document establishes a method for measurement of specific heat capacity, cp, using temperature modulated differential scanning calorimetry.

Технические детали

Технический комитет: ISO/TC 61/SC 5 - Physical-chemical properties
SKU: ISO 19935-2:2020

Abstract

Overview - ISO 19935-2:2020 (Plastics, temperature modulated DSC)

ISO 19935-2:2020 specifies a standardized method for measuring specific heat capacity (cp) of plastics using temperature modulated differential scanning calorimetry (TM-DSC). The document describes measurement principles, apparatus requirements, calibration steps and calculation procedures so that cp data are suitable for data sheets, databases, research, quality assurance and routine material checks.

Key topics and technical requirements

Measurement principle: cp is determined from the amplitude of the modulated heat flow signal; measurement can be done during scanning or in quasi‑isothermal (step scan) modes.
Calculation: the standard gives a formula for cp in terms of the amplitude of the periodic heat flow (ΦA), modulation amplitude of sample temperature (TA), specimen mass (m), angular frequency (ω) and a calibration constant K(ω). Units and conditions are specified to produce cp in J·g⁻¹·K⁻¹.
Step scan option: a step integration method is provided to obtain cp by integrating heat flow over one modulation cycle when appropriate.
Apparatus & temperature control: TM‑DSC must be capable of periodic, stepwise or pulse temperature modulation with amplitude typically in the range ±0.1 to 2.0 K and frequencies down to about 10 mHz, superimposed on an underlying scanning rate typically

Overview - ISO 19935-2:2020 (Plastics, temperature modulated DSC)

Key topics and technical requirements

Measurement principle: cp is determined from the amplitude of the modulated heat flow signal; measurement can be done during scanning or in quasi‑isothermal (step scan) modes.
Calculation: the standard gives a formula for cp in terms of the amplitude of the periodic heat flow (ΦA), modulation amplitude of sample temperature (TA), specimen mass (m), angular frequency (ω) and a calibration constant K(ω). Units and conditions are specified to produce cp in J·g⁻¹·K⁻¹.
Step scan option: a step integration method is provided to obtain cp by integrating heat flow over one modulation cycle when appropriate.
Apparatus & temperature control: TM‑DSC must be capable of periodic, stepwise or pulse temperature modulation with amplitude typically in the range ±0.1 to 2.0 K and frequencies down to about 10 mHz, superimposed on an underlying scanning rate typically

ISO 19935-2:2020 PDF

Технические детали

Abstract

Overview - ISO 19935-2:2020 (Plastics, temperature modulated DSC)

Key topics and technical requirements

Похожие стандарты

Abstract

Overview - ISO 19935-2:2020 (Plastics, temperature modulated DSC)

Key topics and technical requirements

Похожие стандарты

Systems and software engineering — Software life cycle processes

Asset management — Vocabulary, overview and principles

Asset management — Asset management system — Requirements

Information technology — Radio frequency identification device conformance test methods — Part 2: Test method…

Information technology — Multimedia framework (MPEG-21) — Part 22: User Description

Milk — Determination of the lactoperoxidase activity — Photometric method (Reference method)

Carbonaceous materials for the production of aluminium — Cold and tepid ramming pastes — Expansion/shrinkage…

Agricultural machinery — Safety — Part 13: Large rotary mowers