ISO 6509-2:2017 PDF

Corrosion of metals and alloys — Determination of dezincification resistance of copper alloys with zinc — Part 2: Assessment criteria

Первая страница стандарта ISO 6509-2:2017

Открыть превью (PDF)

Название (английский):

ISO 6509-2:2017

Corrosion of metals and alloys — Determination of dezincification resistance of copper alloys with zinc — Part 2: Assessment criteria

Статус документа:: Действующий
Формат:: Электронный (PDF)
Количество страниц:: 3
Дата публикации:: 23 марта 2017 г.
Издание:: ISO IS 6509 edition 1 version 1
ICS:: 77.060

Язык документа:

ruen

Срок поставки:1 раб. дн. (перевод)

Цена:45 €

Описание (английский):

ISO 6509-2:2017 specifies assessment criteria and provides guidance related to the corrosion type dezincification for the selection of copper alloys with a mass fraction of zinc of more than 15 %, exposed to fresh, saline waters or drinking water. The assessment criteria are based on the exposure tests in ISO 6509‑1. The materials can be in the form of a semi-finished product or in the form of a final product (fittings, valves, etc.). ISO 6509-2:2017 is not applicable to complex products like flow-meters or pump-parts. In addition, other properties of the material might need to be taken into account for the intended application. This document is not intended to validate dezincification in case of failure in the application.

Технические детали

Технический комитет: ISO/TC 156 - Corrosion of metals and alloys
SKU: ISO 6509-2:2017

Abstract

Overview

ISO 6509-2:2017 defines assessment criteria and guidance for dezincification resistance of copper‑zinc alloys (brasses) with a zinc mass fraction > 15%, when exposed to fresh water, saline water or drinking water. The criteria are based on exposure tests specified in ISO 6509‑1 (test method) and apply to semi‑finished or finished products such as bars, fittings and valves. ISO 6509‑2:2017 is not intended for complex components (e.g., flow meters, pump parts) and does not validate failures in service.

Key topics and requirements

Scope: Assessment criteria for dezincification in copper alloys with >15% zinc exposed to potable/fresh/saline waters.
Test basis: Acceptance limits rely on dezincification depth measurements obtained using the ISO 6509‑1 exposure/test method.
Minimum requirement: An alloy is classified as dezincification resistant only if both the average and maximum dezincification depths are below the limits in Table 1 (or applicable national limits).
Numeric acceptance criteria (Table 1):
- Final forgings and castings after machining (including continuously cast bars): Average ≤ 100 µm, Maximum ≤ 200 µm
- Extruded bars/profiles for machining - longitudinal direction: Average ≤ 300 µm, Maximum ≤ 400 µm
- Extruded bars/profiles - transverse direction: Average ≤ 100 µm, Maximum ≤ 200 µm
Limitations: Not applicable to complex products; other material properties (mechanical, microbiological, lead content, etc.) may also be required for specific applications. Local water chemistry, flow rate and system management affect dezincification risk and may require stricter limits.

Applications

Selection and specification of dezincification‑resistant brasses for:
- Sanitary installations and plumbing fittings
- Valves and machined components used in drinking water systems
- Manufacturers’ quality control and material acceptance testing
Useful for corrosion engineers, materials engineers, water utilities and procurement teams assessing alloy suitability for potable and saline water environments.

Who should use this standard

Material suppliers and alloy producers
OEMs producing fittings, valves and machined copper alloy parts
Test laboratories performing ISO 6509‑1 exposure tests and reporting compliance to ISO 6509‑2
Specification writers, QA/QC engineers and regulators for water systems

Related standards

ISO 6509‑1 (Test method for dezincification resistance)
ISO 8044 (Corrosion terms and definitions)
Relevant national/product standards: JIS H 3250, EN 12288, NSF/ANSI 14; EN 12163–12168, EN 12420, EN 1982 (for complementary material/product requirements).

Keywords: ISO 6509-2, dezincification, dezincification resistance, copper alloys, brass corrosion, corrosion resistance, drinking water fittings, ISO 6509-1.

Overview

Key topics and requirements

Scope: Assessment criteria for dezincification in copper alloys with >15% zinc exposed to potable/fresh/saline waters.
Test basis: Acceptance limits rely on dezincification depth measurements obtained using the ISO 6509‑1 exposure/test method.
Minimum requirement: An alloy is classified as dezincification resistant only if both the average and maximum dezincification depths are below the limits in Table 1 (or applicable national limits).
Numeric acceptance criteria (Table 1):
- Final forgings and castings after machining (including continuously cast bars): Average ≤ 100 µm, Maximum ≤ 200 µm
- Extruded bars/profiles for machining - longitudinal direction: Average ≤ 300 µm, Maximum ≤ 400 µm
- Extruded bars/profiles - transverse direction: Average ≤ 100 µm, Maximum ≤ 200 µm
Limitations: Not applicable to complex products; other material properties (mechanical, microbiological, lead content, etc.) may also be required for specific applications. Local water chemistry, flow rate and system management affect dezincification risk and may require stricter limits.

Applications

Selection and specification of dezincification‑resistant brasses for:
- Sanitary installations and plumbing fittings
- Valves and machined components used in drinking water systems
- Manufacturers’ quality control and material acceptance testing
Useful for corrosion engineers, materials engineers, water utilities and procurement teams assessing alloy suitability for potable and saline water environments.

Who should use this standard

Material suppliers and alloy producers
OEMs producing fittings, valves and machined copper alloy parts
Test laboratories performing ISO 6509‑1 exposure tests and reporting compliance to ISO 6509‑2
Specification writers, QA/QC engineers and regulators for water systems

Related standards

ISO 6509‑1 (Test method for dezincification resistance)
ISO 8044 (Corrosion terms and definitions)
Relevant national/product standards: JIS H 3250, EN 12288, NSF/ANSI 14; EN 12163–12168, EN 12420, EN 1982 (for complementary material/product requirements).

Keywords: ISO 6509-2, dezincification, dezincification resistance, copper alloys, brass corrosion, corrosion resistance, drinking water fittings, ISO 6509-1.

ISO 6509-2:2017 PDF

Технические детали

Abstract

Overview

Key topics and requirements

Applications

Who should use this standard

Related standards

Похожие стандарты

Abstract

Overview

Key topics and requirements

Applications

Who should use this standard

Related standards

Похожие стандарты

Corrosion of metals and alloys - Determination of dezincification resistance of copper alloys with zinc - Par…

Corrosion of metals and alloys - Vocabulary (ISO 8044:2024)

Systems and software engineering — Software life cycle processes

Asset management — Vocabulary, overview and principles

Asset management — Asset management system — Requirements

Information technology — Radio frequency identification device conformance test methods — Part 2: Test method…

Information technology — Multimedia framework (MPEG-21) — Part 22: User Description

Milk — Determination of the lactoperoxidase activity — Photometric method (Reference method)